Home > Hard Drive > Problem With XP Recognizing DVD & CD Drive In Master Slave

Problem With XP Recognizing DVD & CD Drive In Master Slave

Contents

Onboard or USB Floppy Drive 3. Change any necessary jumpers (see "Setting Jumpers" above) so that both drives as well as a CD drive are recognized. Flag Permalink This was helpful (0) Collapse - New SATA HD booting mantining old IDE HDs. If, however, you are installing a second IDE drive, it is possible that you will need to alter the jumper configuration of your primary hard drive. Source

caution: This product contains components that can be damaged by electrostatic discharge (ESD). This was a very easy task. It sounds like i'm at least on the right path……Here is the exact log… Phoenix ROM BIOS PLUS Version 1.10 A05 Copyright 19854-1988 Phoenix Techmologies LTD. it freezes at the windows loading screen.>i formatted and partitoned the SATA drive wiv the disk writer program from Seagate, and now the SATA switches between being one partition or the

How To Connect Ide Hard Drive To Sata Motherboard

I have a sata HD running as my main drive and another IDE HD, formerly my main one, that I use for music files and backup storage. Some cases use snap-in RF shields, as shown in Figure 8-1, which can be removed using your fingers. The ATA interfaces are located near the right front edge of most motherboards. But after a few more startups, the DVD drive will stop recognizing media in the drive again.

I have no idea about computers and never opened up the box. So you can fix the stuff you own quickly—and get back on with your life. Reply greg says: April 27, 2009 at 9:12 pm I would first try cable select though I cannot verify the results. Ide Hard Drive Jumper Settings How do i remove this data?

Gently remove and reinsert the CD drive data cable from the connector on the motherboard. Sata And Ide Hard Drives Together Replace the CD-ROM with the DVD-RW while your trying this, to avoid complications May 27, 2009 #7 lechevarria89 TS Rookie Topic Starter Posts: 43 Okay, I'll lett you know if Reply sr.robato_pcola_fl says: March 18, 2009 at 5:11 pm nice article! This is my first time to get my hands dirty to install.

This was more than Helpfull in my Latest Conquest!!! How To Make Ide Boot Instead Of Sata but the “Initialize Disk” wizard pop up, wont show up. As you can guess, I took it back to the docal and he said "you fried your mother board and a small fee ($170.00) he could restore my computor and re-install You also need to check that the power cable to the CD/DVD drive is also connected.

Sata And Ide Hard Drives Together

This is because, for an IDE drive, it matters. I think anyone who is attempting to install a new hard drive themselves should embrace the inner geek and get the job done properly… Not that something like this even requires How To Connect Ide Hard Drive To Sata Motherboard No problems in over a year of use. Ide And Sata Drives In Same Computer Take Action It's time to speak out for your right to repair Massachusetts, The people of Massachusetts have always stood up for their right to repair.

I have lots of data on there that I need to keep can I install it without formatting? http://liveterrain.com/hard-drive/wd-hard-drive-for-lap-top.php Then, I decided to uninstall the DVD drive and install my CD-ROM to see if it would recognize it but it didn't. When I insert the CD on the drive I am getting a dialog box that I require 256MB memory. For this, restart the system and run BIOS Setup (you'll need to press a key as your system is booting up; often the key is either F1, F2, Esc or Del). Motherboard With Ide And Sata Ports

Easy to understand! Thanks for the instructions! The hardware-identifying name should appear next to one of the channel listings. have a peek here Helped me over that last hurdle in getting my new drive up and running.

By the way, I grew up in St. What Are The Two Goals When Implementing A Raid Solution IDE hard drives have settings for master, slave and cable select. any suggestions.

Everything seemed OK, until I realized that nothing else happened, the screen doesn't move on to Windows Vista.

my email address is: [emailprotected] thanks Reply dg says: March 10, 2008 at 3:49 pm hi, i hav just purchased a seagate 250GB sata drive. To check this you can either watch the screen as you boot or enter the BIOS itself. There are two things to keep in mind, do not overload your power supply or strange difficult problems will begin to occur and make the correct BIOS settings for your data How Many Hard Drives Can Be Connected To A Single Ide Cable Right-click the drive name and select Enable.

The physical installation is actually pretty easy. Problem is , that there is very little space left on the system drive. Tell your state representative to support S618. http://liveterrain.com/hard-drive/xp-drive-will-not-boot-after-vista-install-on-new-drive.php Now, my DVD-RW drive works!!....

If you subsequently install an additional hard disk or repartition your drive to create additional volumes, the letter assigned to the optical drive may change, which may confuse installed software that You could re-read my post or have someone read it to you. If there are updates available for the CD/DVD drive or recording software, select the ones that apply. Rebuilding a Relic for my Kids.

This full-featured backup/restore utility from a trusted company will help you clone your PC and restore it to your new hard drive. For more information refer to Error in Roxio Creator Basic: The certificate file is missing or has been corrupted. Check with your motherboard manufacturer for updated drivers. Thanks Reply Hans says: November 29, 2008 at 11:38 am Great Article.

Therefore most people can run 6 devices note that each sata connector MUST NOT be shared you may only connect 0 - 2 sata devices and 0 - 4 IDE devices.If All I want to do is upgrade my hard drive. Even for a non-too compuer literate such as myself! With the 4D36E965-E325-11CE-BFC1-08002BE10318 key still selected, right-click any blank area of the right side of the registry editor window (the window pane listing all the values within the key).

Look for your CD/DVD drive in the available list and click the + (plus) sign to expand the menu. Ask a question and give support. Reply Carina says: November 24, 2009 at 2:36 am Hello i wanted to ask, i'm trying to connect a previous sata hard drive onto friends computer to access some files so note: If a missing certificate file message opens, find and delete the hidden file sarlicense9.dat.

Would this be my hard drive. There should be a black (or other coloured) block covering a set of pins. Step 1: Check the drive name in Device Manager If you can use the CD/DVD drive in Windows but your disc recording software does not work (such as Roxio Creator Basic),