Home > Unable To > Setup Unable To Format Drive C:

Setup Unable To Format Drive C:

Contents

Yeah I've never really been sure on how many times you should let it run. I wiped the 40G drive, used 98se boot- disk to fdisk, create partition (leaving rest empty forLinux), made partition active, then XP CD to format andinstall. Glad it worked out. I just burnt the ISO image using deepburner and it booted from the cd no torubles, then ran the tests and it said everthing was fine. check my blog

press enter . Reply ↓ dokimeister November 15, 2014 Hi! Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. Reply ↓ DrDread October 15, 2015 error messages regarding *unable to install to partition *no system reserved partition tried the diskpart method, no dice solution: 1. http://www.tomshardware.com/forum/266731-28-setup-unable-format-partition-disk-damaged

Setup Was Unable To Format The Partition Or Locate An Existing System Partition

If the disk is a SCSI disk, make sure your SCSI devices are properly terminated. There is one identifier "bootmgr", one "current" and one with alot of different letters and numbers… I guess the last one? NOW JUST WANT TO RECOVER RAW FILES TO NTFS:(( Reply ↓ lukas December 17, 2014 man, you are a genius… thks a lot Reply ↓ johan December 18, 2014 I followed

User Name Remember Me? Yeah I've never really been sure on how many times you should let it run. Word of advice to other readers tho: during the "xcopy d: c: /e /k/ h" (close to it) step, those parameters might not be the same for you. Setup Cannot Format The Partition Your Computer May Not Have Enough Memory and, I delete all the partitions.

Backlink is always good, thanks 🙂 Reply ↓ cyrus dj September 4, 2015 how did it work and whats the procedure to install windows 7 while it shows system partition etc Setup Was Unable To Format The Partition The Disk May Be Damaged Windows Xp This is because you need to add another small command to copy over all directories, subdirectories and files within them to make the boot disk work. Reply ↓ Ali February 14, 2015 There is a simpler and different way to solve this problem. http://www.techsupportforum.com/forums/f10/solved-setup-was-unable-to-format-the-partition-573355.html i have try to install windows on each of them but end up with the same msg.i have also trying to install the xp with only 1x 2gb ram but end

Basically you just need to copy all installation files from USB flash drive to your HDD (or SDD) drive and make it bootable, and then continue installation from HDD to HDD Windows Was Unable To Complete The Format Reports: · Posted 5 years ago Top kcting Posts: 59 This post has been reported. Quicker than 14 hrs last time lol Reply ↓ pavle December 9, 2014 THANKS MAN YOU SAVED ME.. Venkatesan October 16, 2015 Thanks a lot.

Setup Was Unable To Format The Partition The Disk May Be Damaged Windows Xp

xcopy x: c: /e /h /k was the command i used (X: beeing my flash drive Reply ↓ bhaguri January 5, 2017 i followed every instruction but nothing happens after computer https://www.cnet.com/forums/discussions/setup-was-unable-to-format-the-partition-119678/ i googled a lot, but could not find any better solution than this.. Setup Was Unable To Format The Partition Or Locate An Existing System Partition on my laptop i went into the bios settings and chose to boot from the usb. Make Sure The Drive Is Switched On And Properly Connected To Your Computer I was installing Win7 on a Dell XPS M1530 and it took me around 5hrs to figure it out… Your guide was so helpful!

This would be a bit of a pain though and of course there is a cost involved, so before I take the plunge I would like to know if anyone else http://liveterrain.com/unable-to/unable-to-run-dds-scr.php From here you can type EXIT to close command. Thanks. and you will need at least 20000MB which equals to 20GBs for Installation.. Setup Was Unable To Create The Partition

Any help would be much appreciated. Thanks again and you are the best! I've run a thorough diagnostics test on my hard drive and there are no errors there. news The Kensington Sticks don't work (as I think they are USB 3.0).

You must press the F6 key and provide SATA drivers, or the setup will not be able to detect your drive. 0Votes Share Flag Collapse - As Thumbs has stated by I work around bum boards by using a PCI USB 2.0 card.There is also some boards that have USB 2.0 timing issues that vanish when you put an USB 2.0 hub And i see alot of questions about drive letters.

i unable to format my external hard-disk.

The installation will begin. You are a star man, Keep it man, (This is my first time commenting on pages like these) Reply ↓ Josh November 8, 2014 Holy shitballs it actually worked. When I use the xcopy command I get an error saying ‘The system cannot find the file specified'. Reply ↓ kesav July 10, 2015 Dear druss im also facing same prob but im cant complete yr steps…..

and left the rest unallocated. Worked for me!!! In my case the command was: xcopy d: f: 3: Also in Step 4, the listed copy command only copied over 3 files, when the correct number should be 877 for http://liveterrain.com/unable-to/problems-when-trying-to-format.php I suspect there's a lot of wasted space from these items, but some things look like necessary Windows components (like C:\boot or C:\System Volume Information, etc.).

Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc. Tarzo, Jan 1, 2009 #10 Elvandil Joined: Aug 1, 2003 Messages: 51,988 I hope you're right. Just boot from the cd and have a look at the tools on there Reports: · Posted 5 years ago Top LH Posts: 20002 This post has been reported. The disk may be damaged.